模具專業術語(中英)一,入水:gate 進入位: gate location 水口形式:gate type 大水口:edge gate 細水口: pin-point gate 水口大小:gate size 轉水口: switching runner/gate 唧嘴口徑: sprue diameter 二,流道: runner 熱流道: hot runner,hot manifold 熱嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圓形流道:round(full/half runner 流道電腦分析:mold flow analysis 流道平衡:runner balance 熱嘴: hot sprue 熱流道板:hot manifold 發熱管:cartridge heater 探針: thermocouples 插頭: connector plug 插座: connector socket 密封/封料: seal 三,運水:water line 喉塞:line lpug 喉管:tube 塑膠管:plastic tube 快速接頭:jiffy quick connector plug/socker 四,模具零件: mold components 三板模:3-plate mold 二板模:2-plate mold 邊釘/導邊:leader pin/guide pin 邊司/導套:bushing/guide bushing 中托司:shoulder guide bushing 中托邊 L:guide pin 頂針板:ejector retainner plate 托板: support plate 螺絲: screw 管釘:dowel pin 開模槽:ply bar scot 內模管位:core/cavity inter-lock 頂針: ejector pin 司筒:ejector sleeve 司筒針:ejector pin 推板:stripper plate縮呵:movable core,return core core puller 扣機(尼龍拉勾) :nylon latch lock 斜頂:lifter 模胚(架) mold base : 上內模:cavity insert 下內模:core insert 行位(滑塊) slide : 鑲件:insert 壓座/斜雞:wedge 耐磨板/油板:wedge wear plate 壓條 plate 撐頭: support pillar 唧嘴: sprue bushing 擋板:stop plate 定位圈:locating ring 鎖扣:latch 扣雞:parting lock set 推桿:push bar 栓打螺絲:S.H.S.B 頂板:eracuretun 活動臂:lever arm 分流錐:spure sperader 水口司:bush 垃圾釘:stop pin 隔片:buffle 彈弓柱:spring rod 彈弓:die spring 中托司:ejector guide bush 中托邊:ejector guide pin 鑲針:pin 銷子:dowel pin 波子彈弓:ball catch 喉塞: pipe plug 鎖模塊:lock plate 斜頂:angle from pin 斜頂桿:angle ejector rod 尼龍拉勾:parting locks 活動臂:lever arm 復位鍵,提前回桿:early return bar 氣閥:valves 斜導邊:angle pin 術語:terms 承壓平面平衡:parting surface support balance 模排氣:parting line venting回針碰料位:return pin and cavity interference ?？偢叱銎C規格:mold base shut hight 頂針碰運水:water line interferes withejector pin 料位出上/下模:part from cavith (core) side 模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate. 不準用鑲件: Do not use (core/cavity) insert 用鈹銅做鑲件: use beryllium copper insert 初步(正式)模圖設計:preliinary (final) mold design 反呵:reverse core 彈弓壓縮量:spring compressed length 穩定性好:good stability,stable 強度不夠:insufficient rigidity 均勻冷卻:even cooling 扣模:sticking 熱膨脹:thero expansion 公差:tolorance 銅公(電極) :copper electrode 補充:模具常用英文縮寫與其解釋